Aluminum Composite Panel (ACM) vs PET Foam Core
Composite · grade comparison
Aluminum Composite Panel (ACM) and PET Foam Core are both composite grades. Aluminum Composite Panel (ACM) is the stronger of the two: tensile strength 130 MPa (18.9 ksi) against 2 MPa (0.232 ksi) for PET Foam Core, about 81 times as much. PET Foam Core is lighter (0.1 g/cm³ vs 1.35 g/cm³ for Aluminum Composite Panel (ACM)) and Aluminum Composite Panel (ACM) is stiffer (70 GPa vs 0.1 GPa). On the shop floor, PET Foam Core machines more easily (excellent vs very good) and Aluminum Composite Panel (ACM) sits in a lower cost tier (standard, $$) than PET Foam Core (premium, $$$).
Aluminum Composite Panel (ACM)Choose it when strength drives the design, or when cost is the deciding factor.
PET Foam CoreChoose it when weight is the constraint, or when the part sees heat.
Aluminum Composite Panel (ACM) vs PET Foam Core: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Aluminum Composite Panel (ACM)PET Foam Core
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Modulus
Poisson's Ratio
Compressive Strength
Compressive Modulus
Shear Strength
Physical
Density and transition temperatures.
Density
Melting Temperature (Tm)
Glass Transition (Tg)
Water Absorption (24 h)
Water Absorption (Saturation)
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Specific Heat Capacity
Limiting Oxygen Index
Max Service Temperature (short-term)
Electrical
Conductivity and insulation.
Dielectric Constant (1 MHz)
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
UV / Weathering Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Same in both: Thermal Shock Resistance Index 0
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Aluminum Composite Panel (ACM) | PET Foam Core |
|---|---|---|
| Sheet metal | Yes | — |
| Default condition | PE Core | — |
| Relative cost | $$ Standard | $$$ Premium |
| Min. machined wall | — | — |
| Best machined surface | — | — |
| Painting | Yes | — |
Aluminum Composite Panel (ACM) vs PET Foam Core — frequently asked
Is Aluminum Composite Panel (ACM) stronger than PET Foam Core?
Yes. Aluminum Composite Panel (ACM) has a typical tensile strength of 130 MPa (18.9 ksi) against 2 MPa (0.232 ksi) for PET Foam Core — about 81 times as much.
Which is cheaper, Aluminum Composite Panel (ACM) or PET Foam Core?
Aluminum Composite Panel (ACM) is the lower-cost material: it sits in the standard tier ($$) while PET Foam Core is premium ($$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, Aluminum Composite Panel (ACM) or PET Foam Core?
PET Foam Core. Its machinability rates excellent (92/100) against very good (80/100) for Aluminum Composite Panel (ACM).
Ready to make it?
Upload a CAD file and FabDigit prices the part in Aluminum Composite Panel (ACM) and PET Foam Core side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.