5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 vs 5052-H39 Aluminum Honeycomb CR
Composite · 5052-H39 Aluminum Honeycomb grade comparison
5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 and 5052-H39 Aluminum Honeycomb CR are two grades of the same composite grade, 5052-H39 Aluminum Honeycomb: 1.6-1/4-.0007 (1.6 pcf) versus CR (cold rolled). The chemistry is identical, so every difference below comes from the condition. 5052-H39 Aluminum Honeycomb CR is the stronger of the two: yield strength 1 MPa (0.189 ksi) against 0.45 MPa (0.0653 ksi) for 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007, about 189% more; tensile strength follows at 2 MPa (0.276 ksi) vs 1 MPa (0.145 ksi). 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 is lighter (0.03 g/cm³ vs 0.05 g/cm³ for 5052-H39 Aluminum Honeycomb CR) and 5052-H39 Aluminum Honeycomb CR is stiffer (0.52 GPa vs 0.21 GPa).
5052-H39 Aluminum Honeycomb 1.6-1/4-.0007Choose it when weight is the constraint.
5052-H39 Aluminum Honeycomb CRChoose it when strength drives the design.
5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 vs 5052-H39 Aluminum Honeycomb CR: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all composite grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
5052-H39 Aluminum Honeycomb 1.6-1/4-.00075052-H39 Aluminum Honeycomb CR
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Shear Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Compressive Strength
Compressive Modulus
Shear Strength
Same in both: Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Density
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 900 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.8 µm/m·K13.2 µin/in·°F · Min Service Temperature -196°C-321 °F · Max Service Temperature (short-term) 250°C482 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: UV / Weathering Resistance 95 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 215 MJ/kg92,433 BTU/lb · Embodied Carbon (primary production) 14 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 10%
Strength versus weight
Yield strength against density for every composite grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 vs 5052-H39 Aluminum Honeycomb CR — frequently asked
Is 5052-H39 Aluminum Honeycomb CR stronger than 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007?
Yes. 5052-H39 Aluminum Honeycomb CR has a typical yield strength of 1 MPa (0.189 ksi) against 0.45 MPa (0.0653 ksi) for 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 — about 189% more. Tensile strength is 2 MPa (0.276 ksi) vs 1 MPa (0.145 ksi).
Which grade does FabDigit quote by default, 1.6-1/4-.0007 or CR?
3.1-1/8-.0007 is the default 5052-H39 Aluminum Honeycomb condition in the FabDigit quote flow (neither 1.6-1/4-.0007 nor CR). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 or 5052-H39 Aluminum Honeycomb CR?
5052-H39 Aluminum Honeycomb CR. Its machinability rates fair (38/100) against poor (30/100) for 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 5052-H39 Aluminum Honeycomb 1.6-1/4-.0007 and 5052-H39 Aluminum Honeycomb CR side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.