Cobalt-Chrome Alloy Elgiloy-ANN vs Elgiloy CW-1/2H
Cobalt-Chrome Alloy · Elgiloy temper comparison
Elgiloy-ANN and Elgiloy CW-1/2H are two conditions of the same cobalt-chrome alloy grade, Elgiloy: ANN (annealed) versus CW-1/2H (cold worked ~30–40 %). The chemistry is identical, so every difference below comes from the condition. Elgiloy CW-1/2H is the stronger of the two: yield strength 1,250 MPa (181 ksi) against 480 MPa (69.6 ksi) for Elgiloy-ANN, about 160% more; tensile strength follows at 1,500 MPa (218 ksi) vs 1,000 MPa (145 ksi). In exchange, Elgiloy-ANN is the more ductile: elongation 55% versus 12% for Elgiloy CW-1/2H, and Elgiloy CW-1/2H is harder (45 HRC vs 22 HRC). Elgiloy CW-1/2H is stiffer (200 GPa vs 190 GPa) and Elgiloy-ANN runs hotter in service (500°C vs 350°C continuous). On the shop floor, Elgiloy-ANN welds better (good vs fair).
Elgiloy-ANNChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
Elgiloy CW-1/2HChoose it when strength drives the design.
Elgiloy-ANN vs Elgiloy CW-1/2H: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all cobalt-chrome alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all cobalt-chrome alloy grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Rockwell C
Hardness, Vickers
Same in both: Shear Modulus 80 GPa11.6 Msi · Bulk Modulus 175 GPa25.4 Msi · Poisson's Ratio 0.3
Physical
Density and transition temperatures.
Same in both: Density 8.3 g/cm³0.3 lb/in³ · Melting Point (Solidus) 1,400°C2,552 °F · Liquidus Temperature 1,450°C2,642 °F
Thermal
How each material carries heat and how hot it can run.
Max Service Temperature (continuous)
Same in both: Thermal Conductivity 12.5 W/m·K7.2 BTU/hr·ft·°F · Specific Heat Capacity 430 J/kg·K0.1 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 15 µm/m·K8.3 µin/in·°F · Latent Heat of Fusion 280 J/g120 BTU/lb · Min Service Temperature -269°C-452 °F
Electrical
Conductivity and insulation.
Electrical Resistivity
Same in both: Electrical Conductivity 1.7 % IACS
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.2 V · Corrosion Resistance 88 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Weldability
Formability (cold)
Same in both: Machinability Rating (AISI 1212 = 100 %) 12% · Castability 25 / 100 · Brazeability / Solderability 55 / 100 · Polishability 85 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 165 MJ/kg70,937 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 500 L/kg59.9 gal/lb · Typical Recycled Content 20%
Strength versus weight
Yield strength against density for every cobalt-chrome alloy grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Elgiloy-ANN vs Elgiloy CW-1/2H — frequently asked
Is Elgiloy CW-1/2H stronger than Elgiloy-ANN?
Yes. Elgiloy CW-1/2H has a typical yield strength of 1,250 MPa (181 ksi) against 480 MPa (69.6 ksi) for Elgiloy-ANN — about 160% more. Tensile strength is 1,500 MPa (218 ksi) vs 1,000 MPa (145 ksi).
Which condition does FabDigit quote by default, ANN or CW-1/2H?
CWA is the default Elgiloy condition in the FabDigit quote flow (neither ANN nor CW-1/2H). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which welds better, Elgiloy-ANN or Elgiloy CW-1/2H?
Elgiloy-ANN. Its weldability rates good (55/100) against fair (40/100) for Elgiloy CW-1/2H.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Elgiloy-ANN and Elgiloy CW-1/2H side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.