Impervious Graphite vs RP Graphite Electrode
Ceramic · grade comparison
Impervious Graphite and RP Graphite Electrode are both ceramic grades. Impervious Graphite is the stronger of the two: tensile strength 25 MPa (3.63 ksi) against 7 MPa (1.02 ksi) for RP Graphite Electrode, about 3.6 times as much. Impervious Graphite is the more ductile: elongation 0.3% versus 0.25% for RP Graphite Electrode, and Impervious Graphite is harder (50 HV vs 32 HV). RP Graphite Electrode is lighter (1.56 g/cm³ vs 1.8 g/cm³ for Impervious Graphite) and Impervious Graphite is stiffer (12 GPa vs 9 GPa). On the shop floor, RP Graphite Electrode machines more easily (excellent vs very good) and RP Graphite Electrode sits in a lower cost tier (standard, $$) than Impervious Graphite (high, $$$$).
Impervious GraphiteChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
RP Graphite ElectrodeChoose it when weight is the constraint, or when the part sees heat.
Impervious Graphite vs RP Graphite Electrode: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all ceramic grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all ceramic grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Impervious GraphiteRP Graphite Electrode
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Elastic (Young's) Modulus
Poisson's Ratio
Tensile Strength (Ultimate)
Elongation at Break
Compressive Strength
Flexural Strength
Shear Strength
Fracture Toughness (K_IC)
Hardness, Vickers
Hardness, Mohs
Shear Modulus
Physical
Density and transition temperatures.
Density
Porosity
Melting Point (Solidus)
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Thermal Expansion (CTE, 20–100 °C)
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Specific Heat Capacity 710 J/kg·K0.17 BTU/lb·°F
Electrical
Conductivity and insulation.
Electrical Resistivity
Volume Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Polishability
Sintering / Firing Temperature
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Embodied Water
Common Calculations
Ratios derived from the values above.
Specific Strength (UTS / density)
Specific Stiffness (E / density)
Thermal Diffusivity
Thermal Shock Resistance Index
Strength versus weight
Yield strength against density for every ceramic grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Manufacturing and finishing
| Capability | Impervious Graphite | RP Graphite Electrode |
|---|---|---|
| Default condition | — | — |
| Relative cost | $$$$ High | $$ Standard |
| Min. machined wall | — | — |
| Best machined surface | — | — |
Impervious Graphite vs RP Graphite Electrode — frequently asked
Is Impervious Graphite stronger than RP Graphite Electrode?
Yes. Impervious Graphite has a typical tensile strength of 25 MPa (3.63 ksi) against 7 MPa (1.02 ksi) for RP Graphite Electrode — about 3.6 times as much.
Which is cheaper, Impervious Graphite or RP Graphite Electrode?
RP Graphite Electrode is the lower-cost material: it sits in the standard tier ($$) while Impervious Graphite is high ($$$$). Part price depends far more on geometry, tolerance and quantity than on raw stock — upload a CAD file for a live quote.
Which is easier to machine, Impervious Graphite or RP Graphite Electrode?
RP Graphite Electrode. Its machinability rates excellent (90/100) against very good (80/100) for Impervious Graphite.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Impervious Graphite and RP Graphite Electrode side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.