Aluminum Al-Ce-AB vs Al-Ce-F
Aluminum · Al-Ce temper comparison
Al-Ce-AB and Al-Ce-F are two conditions of the same aluminum grade, Al-Ce: AB (as built (as printed)) versus F (as fabricated). The chemistry is identical, so every difference below comes from the condition. Al-Ce-AB is the stronger of the two: yield strength 320 MPa (46.4 ksi) against 115 MPa (16.7 ksi) for Al-Ce-F, about 178% more; tensile strength follows at 420 MPa (60.9 ksi) vs 200 MPa (29 ksi). Al-Ce-AB is the more ductile: elongation 8% versus 5% for Al-Ce-F, and Al-Ce-AB is harder (100 HB vs 62 HB). Al-Ce-F runs hotter in service (300°C vs 250°C continuous) and Al-Ce-F conducts heat better (135 W/m·K vs 100 W/m·K). On the shop floor, Al-Ce-F machines more easily (very good vs good).
Al-Ce-ABChoose it when strength drives the design, or when the part is bent, formed or impact-loaded.
Al-Ce-FChoose it when the part sees heat, or when the part is machined in volume.
Al-Ce-AB vs Al-Ce-F: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 74 GPa10.7 Msi · Shear Modulus 27.5 GPa4 Msi · Bulk Modulus 73 GPa10.6 Msi · Poisson's Ratio 0.33 · Compressive Strength 340 MPa49.3 ksi · Shear Strength 250 MPa36.3 ksi · Fracture Toughness (K_IC) 20 MPa·√m18.2 ksi·√in · Charpy V-Notch Impact (RT) 6 J4.4 ft·lbf · Hardness, Rockwell B 60 HRB
Physical
Density and transition temperatures.
Same in both: Density 2.8 g/cm³0.1 lb/in³ · Melting Point (Solidus) 640°C1,184 °F · Liquidus Temperature 655°C1,211 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 890 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 22 µm/m·K12.2 µin/in·°F · Latent Heat of Fusion 380 J/g163 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 5.7×10⁻⁸ Ω·m2.24 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Same in both: Galvanic Potential (seawater, vs SCE) -0.75 V · Corrosion Resistance 55 / 100
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Machinability Rating (AISI 1212 = 100 %) 90% · Weldability 75 / 100 · Formability (cold) 30 / 100 · Castability 88 / 100 · Brazeability / Solderability 35 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 235 MJ/kg101,032 BTU/lb · Embodied Carbon (primary production) 14 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 5%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
Al-Ce-AB vs Al-Ce-F — frequently asked
Is Al-Ce-AB stronger than Al-Ce-F?
Yes. Al-Ce-AB has a typical yield strength of 320 MPa (46.4 ksi) against 115 MPa (16.7 ksi) for Al-Ce-F — about 178% more. Tensile strength is 420 MPa (60.9 ksi) vs 200 MPa (29 ksi).
Which condition does FabDigit quote by default, AB or F?
AB is the default Al-Ce condition in the FabDigit quote flow. The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, Al-Ce-AB or Al-Ce-F?
Al-Ce-F. Its machinability rates very good (70/100) against good (58/100) for Al-Ce-AB.
Ready to make it?
Upload a CAD file and FabDigit prices the part in Al-Ce-AB and Al-Ce-F side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.