Aluminum 7B04-T651 vs 7B04-T73
Aluminum · 7B04 temper comparison
7B04-T651 and 7B04-T73 are two conditions of the same aluminum grade, 7B04: T651 (T6, stress relieved by stretching) versus T73 (solution heat treated and overaged for stress-corrosion resistance). The chemistry is identical, so every difference below comes from the condition. 7B04-T651 is the stronger of the two: yield strength 465 MPa (67.4 ksi) against 405 MPa (58.7 ksi) for 7B04-T73, about 15% more; tensile strength follows at 535 MPa (77.6 ksi) vs 480 MPa (69.6 ksi). 7B04-T651 is harder — 150 HB against 135 HB for 7B04-T73 — which matters for wear surfaces and threads. 7B04-T73 runs hotter in service (150°C vs 120°C continuous) and 7B04-T73 conducts heat better (155 W/m·K vs 130 W/m·K).
7B04-T651Choose it when strength drives the design, or when surface hardness matters.
7B04-T73Choose it when the part sees heat.
7B04-T651 vs 7B04-T73: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33 · Hardness, Vickers 165 HV
Physical
Density and transition temperatures.
Same in both: Density 2.85 g/cm³0.1 lb/in³ · Melting Point (Solidus) 477°C891 °F · Liquidus Temperature 635°C1,175 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 960 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.4 µm/m·K13 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 5.2×10⁻⁸ Ω·m2.05 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.83 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Formability (cold)
Same in both: Weldability 15 / 100 · Brazeability / Solderability 10 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 13 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 5%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7B04-T651 vs 7B04-T73 — frequently asked
Is 7B04-T651 stronger than 7B04-T73?
Yes. 7B04-T651 has a typical yield strength of 465 MPa (67.4 ksi) against 405 MPa (58.7 ksi) for 7B04-T73 — about 15% more. Tensile strength is 535 MPa (77.6 ksi) vs 480 MPa (69.6 ksi).
Which condition does FabDigit quote by default, T651 or T73?
T6 is the default 7B04 condition in the FabDigit quote flow (neither T651 nor T73). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 7B04-T651 or 7B04-T73?
7B04-T651, by a small margin. Both rate very good for machinability — 75/100 against 70/100 for 7B04-T73.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7B04-T651 and 7B04-T73 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.