Aluminum 7175-O vs 7175-T651
Aluminum · 7175 temper comparison
7175-O and 7175-T651 are two conditions of the same aluminum grade, 7175: O (annealed) versus T651 (T6, stress relieved by stretching). The chemistry is identical, so every difference below comes from the condition. 7175-T651 is the stronger of the two: yield strength 515 MPa (74.7 ksi) against 105 MPa (15.2 ksi) for 7175-O, about 4.9 times as much; tensile strength follows at 585 MPa (84.8 ksi) vs 230 MPa (33.4 ksi). In exchange, 7175-O is the more ductile: elongation 17% versus 11% for 7175-T651, and 7175-T651 is harder (150 HB vs 60 HB). 7175-O runs hotter in service (200°C vs 150°C continuous) and 7175-O conducts heat better (173 W/m·K vs 130 W/m·K). On the shop floor, 7175-T651 machines more easily (very good vs good).
7175-OChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
7175-T651Choose it when strength drives the design, or when the part is machined in volume.
7175-O vs 7175-T651: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Reduction in Area
Compressive Strength
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 71.7 GPa10.4 Msi · Shear Modulus 26.9 GPa3.9 Msi · Bulk Modulus 70 GPa10.2 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.8 g/cm³0.1 lb/in³ · Melting Point (Solidus) 477°C891 °F · Liquidus Temperature 635°C1,175 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 960 J/kg·K0.23 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23.4 µm/m·K13 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.8 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 8 / 100 · Polishability 60 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 8%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
7175-O vs 7175-T651 — frequently asked
Is 7175-T651 stronger than 7175-O?
Yes. 7175-T651 has a typical yield strength of 515 MPa (74.7 ksi) against 105 MPa (15.2 ksi) for 7175-O — about 4.9 times as much. Tensile strength is 585 MPa (84.8 ksi) vs 230 MPa (33.4 ksi).
Which condition does FabDigit quote by default, O or T651?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 7175-O or 7175-T651?
7175-T651. Its machinability rates very good (80/100) against good (55/100) for 7175-O.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 7175-O and 7175-T651 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.