Aluminum 3004-H112 vs 3004-H32
Aluminum · 3004 temper comparison
3004-H112 and 3004-H32 are two conditions of the same aluminum grade, 3004: H112 (strain hardened from hot working only) versus H32 (strain hardened and stabilized, quarter hard). The chemistry is identical, so every difference below comes from the condition. 3004-H32 is the stronger of the two: yield strength 170 MPa (24.7 ksi) against 85 MPa (12.3 ksi) for 3004-H112, about 100% more; tensile strength follows at 215 MPa (31.2 ksi) vs 185 MPa (26.8 ksi). 3004-H32 is harder — 52 HB against 46 HB for 3004-H112 — which matters for wear surfaces and threads. 3004-H112 runs hotter in service (175°C vs 150°C continuous).
3004-H112Choose it when the part sees heat.
3004-H32Choose it when strength drives the design, or when surface hardness matters.
3004-H112 vs 3004-H32: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Bulk Modulus
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 69 GPa10 Msi · Shear Modulus 26 GPa3.8 Msi · Poisson's Ratio 0.33 · Compressive Strength 205 MPa29.7 ksi
Physical
Density and transition temperatures.
Same in both: Density 2.72 g/cm³0.1 lb/in³ · Melting Point (Solidus) 629°C1,164 °F · Liquidus Temperature 654°C1,209 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Expansion (CTE, 20–100 °C)
Latent Heat of Fusion
Max Service Temperature (continuous)
Min Service Temperature
Same in both: Thermal Conductivity 163 W/m·K94.2 BTU/hr·ft·°F · Specific Heat Capacity 893 J/kg·K0.21 BTU/lb·°F
Electrical
Conductivity and insulation.
Same in both: Electrical Conductivity 42 % IACS · Electrical Resistivity 4.1×10⁻⁸ Ω·m1.61 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.84 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 45 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Embodied Energy (primary production)
Embodied Carbon (primary production)
Typical Recycled Content
Same in both: Embodied Water 1,200 L/kg144 gal/lb
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
3004-H112 vs 3004-H32 — frequently asked
Is 3004-H32 stronger than 3004-H112?
Yes. 3004-H32 has a typical yield strength of 170 MPa (24.7 ksi) against 85 MPa (12.3 ksi) for 3004-H112 — about 100% more. Tensile strength is 215 MPa (31.2 ksi) vs 185 MPa (26.8 ksi).
Which condition does FabDigit quote by default, H112 or H32?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 3004-H112 or 3004-H32?
3004-H32, by a small margin. Both rate fair for machinability — 45/100 against 40/100 for 3004-H112; for welding the order is 3004-H32 first (excellent, 88/100) then 3004-H112 (very good, 80/100).
Ready to make it?
Upload a CAD file and FabDigit prices the part in 3004-H112 and 3004-H32 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.