Aluminum 242.0-T61 vs 242.0-T7
Aluminum · 242.0 temper comparison
242.0-T61 and 242.0-T7 are two conditions of the same aluminum grade, 242.0: T61 (T6 variant, underaged) versus T7 (solution heat treated and overaged (stabilized)). The chemistry is identical, so every difference below comes from the condition. 242.0-T61 is the stronger of the two: yield strength 290 MPa (42.1 ksi) against 159 MPa (23.1 ksi) for 242.0-T7, about 82% more; tensile strength follows at 324 MPa (47 ksi) vs 207 MPa (30 ksi). In exchange, 242.0-T7 is the more ductile: elongation 2% versus 0.5% for 242.0-T61, and 242.0-T61 is harder (110 HB vs 75 HB). 242.0-T7 runs hotter in service (260°C vs 200°C continuous) and 242.0-T7 conducts electricity better (38 % IACS vs 33 % IACS).
242.0-T61Choose it when strength drives the design.
242.0-T7Choose it when the part is bent, formed or impact-loaded, or when the part sees heat.
242.0-T61 vs 242.0-T7: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Charpy V-Notch Impact (RT)
Hardness, Brinell
Same in both: Elastic (Young's) Modulus 71 GPa10.3 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33 · Fracture Toughness (K_IC) 17 MPa·√m15.5 ksi·√in
Physical
Density and transition temperatures.
Same in both: Density 2.81 g/cm³0.1 lb/in³ · Melting Point (Solidus) 528°C982 °F · Liquidus Temperature 635°C1,175 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 921 J/kg·K0.22 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 22.5 µm/m·K12.5 µin/in·°F · Latent Heat of Fusion 389 J/g167 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Same in both: Electrical Resistivity 5.1×10⁻⁸ Ω·m2.01 µΩ·in
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.72 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Same in both: Weldability 22 / 100 · Formability (cold) 5 / 100 · Castability 48 / 100 · Brazeability / Solderability 15 / 100 · Polishability 45 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 11.5 kg CO₂/kg · Embodied Water 1,150 L/kg138 gal/lb · Typical Recycled Content 45%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
242.0-T61 vs 242.0-T7 — frequently asked
Is 242.0-T61 stronger than 242.0-T7?
Yes. 242.0-T61 has a typical yield strength of 290 MPa (42.1 ksi) against 159 MPa (23.1 ksi) for 242.0-T7 — about 82% more. Tensile strength is 324 MPa (47 ksi) vs 207 MPa (30 ksi).
Which condition does FabDigit quote by default, T61 or T7?
T5 is the default 242.0 condition in the FabDigit quote flow (neither T61 nor T7). The other condition is available on request or by drawing note — specify it in the material field or the part notes and the quote is priced for it.
Which is easier to machine, 242.0-T61 or 242.0-T7?
242.0-T61. Its machinability rates very good (75/100) against good (68/100) for 242.0-T7.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 242.0-T61 and 242.0-T7 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.