Aluminum 2030-O vs 2030-T3
Aluminum · 2030 temper comparison
2030-O and 2030-T3 are two conditions of the same aluminum grade, 2030: O (annealed) versus T3 (solution heat treated, cold worked and naturally aged). The chemistry is identical, so every difference below comes from the condition. 2030-T3 is the stronger of the two: yield strength 310 MPa (45 ksi) against 85 MPa (12.3 ksi) for 2030-O, about 3.6 times as much; tensile strength follows at 410 MPa (59.5 ksi) vs 190 MPa (27.6 ksi). In exchange, 2030-O is the more ductile: elongation 20% versus 10% for 2030-T3, and 2030-T3 is harder (105 HB vs 48 HB). 2030-O runs hotter in service (150°C vs 100°C continuous) and 2030-O conducts heat better (180 W/m·K vs 130 W/m·K). On the shop floor, 2030-T3 machines more easily (excellent vs very good).
2030-OChoose it when the part is bent, formed or impact-loaded, or when the part sees heat.
2030-T3Choose it when strength drives the design, or when the part is machined in volume.
2030-O vs 2030-T3: propertiesHow to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
How to read these bars
- One bar per material. A full bar is the highest value among all aluminum grades in the FabDigit library; each bar is drawn as a share of that.
- The better value (by the usual engineering direction) is in bold. Rows with no direction — density, thermal conductivity — have no bold.
- Values are typical room-temperature figures for the condition named on each card.
- Confirm against the certified mill or resin datasheet before design release.
Mechanical
Strength, stiffness, ductility and hardness at room temperature.
Tensile Strength (Ultimate)
Yield Strength (0.2% offset)
Elongation at Break
Shear Strength
Fatigue Strength (Endurance Limit)
Fracture Toughness (K_IC)
Hardness, Brinell
Hardness, Vickers
Same in both: Elastic (Young's) Modulus 73 GPa10.6 Msi · Shear Modulus 27 GPa3.9 Msi · Bulk Modulus 71 GPa10.3 Msi · Poisson's Ratio 0.33
Physical
Density and transition temperatures.
Same in both: Density 2.82 g/cm³0.1 lb/in³ · Melting Point (Solidus) 510°C950 °F · Liquidus Temperature 640°C1,184 °F
Thermal
How each material carries heat and how hot it can run.
Thermal Conductivity
Max Service Temperature (continuous)
Same in both: Specific Heat Capacity 870 J/kg·K0.21 BTU/lb·°F · Thermal Expansion (CTE, 20–100 °C) 23 µm/m·K12.8 µin/in·°F · Latent Heat of Fusion 390 J/g168 BTU/lb · Min Service Temperature -196°C-321 °F
Electrical
Conductivity and insulation.
Electrical Conductivity
Electrical Resistivity
Chemical & Environmental
Corrosion and environmental resistance (0–100 scores).
Corrosion Resistance
Same in both: Galvanic Potential (seawater, vs SCE) -0.69 V
Manufacturability
FabDigit workshop ratings (0–100 scores) — how each material behaves on the machine.
Machinability
Machinability Rating (AISI 1212 = 100 %)
Weldability
Formability (cold)
Same in both: Brazeability / Solderability 10 / 100 · Polishability 55 / 100
Sustainability
Primary-production footprint per kilogram.
Same in both: Embodied Energy (primary production) 205 MJ/kg88,134 BTU/lb · Embodied Carbon (primary production) 12.5 kg CO₂/kg · Embodied Water 1,200 L/kg144 gal/lb · Typical Recycled Content 10%
Strength versus weight
Yield strength against density for every aluminum grade in the FabDigit library; the compared grades are highlighted. Up and left is stronger for its weight.
2030-O vs 2030-T3 — frequently asked
Is 2030-T3 stronger than 2030-O?
Yes. 2030-T3 has a typical yield strength of 310 MPa (45 ksi) against 85 MPa (12.3 ksi) for 2030-O — about 3.6 times as much. Tensile strength is 410 MPa (59.5 ksi) vs 190 MPa (27.6 ksi).
Which condition does FabDigit quote by default, O or T3?
Specify the condition in the material field or the drawing note; FabDigit prices the quote for the state you call out.
Which is easier to machine, 2030-O or 2030-T3?
2030-T3. Its machinability rates excellent (95/100) against very good (70/100) for 2030-O.
Ready to make it?
Upload a CAD file and FabDigit prices the part in 2030-O and 2030-T3 side by side — material, machining time, tolerance and finish in one quote. Certified material data ships with the order on request.
Typical handbook values for the conditions named above, normalised for comparison. Hardness on non-Brinell scales is converted approximately for charting only. Request certified data with your order for design-critical properties.