Steel DC01 · finish state
Steel DC01-EG
Properties of the EG condition, compared with the other DC01 tempers.
Choose when a smooth paintable surface and tight thickness control matter more than coating life — thin zinc for indoor enclosures and appliance panels.
What is DC01-EG?
DC01-EG is DC01 supplied in the EG condition — choose when a smooth paintable surface and tight thickness control matter more than coating life — thin zinc for indoor enclosures and appliance panels. DC01-EG has a yield strength of 210 MPa (30.5 ksi) and a tensile strength of 310 MPa (45 ksi) — weaker than 98% of steel grades. Elongation at break is 32% and the elastic modulus is 210 GPa (30.5 Msi). DC01-EG has a density of 7.85 g/cm³ (0.284 lb/in³), heavier than 56% of steel grades. It melts at 1,495°C (2,723 °F). HR is the default condition FabDigit quotes; EG is available on request or by drawing note.
Advantages
- Conducts heat well — 52 W/m·K (30 BTU/hr·ft·°F), better than 98% of steel grades
- Ductile — tolerates forming and impact — 32%, better than 95% of steel grades
- High electrical conductivity — 10.8 % IACS, better than 94% of steel grades
- Forms and bends easily — 80/100, better than 92% of steel grades
- Good corrosion resistance — 22/100, better than 89% of steel grades
Limitations
- Low strength — 210 MPa (30.5 ksi), worse than 98% of steel grades
- Limited service temperature — 200°C (392 °F), worse than 93% of steel grades
- Hard to polish — 45/100, worse than 84% of steel grades
DC01-EG properties
Typical room-temperature values for DC01-EG — 11 properties are specific to this condition; the rest are grade-level values shared by every DC01 temper. Each bar shows where the value sits among the steel grades in FabDigit's library — further right is higher.
Physical3
DC01-EG has a density of 7.85 g/cm³ (0.284 lb/in³), heavier than 56% of steel grades. It melts at 1,495°C (2,723 °F).
Mechanical13
DC01-EG has a yield strength of 210 MPa (30.5 ksi) and a tensile strength of 310 MPa (45 ksi) — weaker than 98% of steel grades. Elongation at break is 32% and the elastic modulus is 210 GPa (30.5 Msi).
Thermal6
DC01-EG is rated for continuous service to 200°C (392 °F). It conducts heat at 52 W/m·K (30 BTU/hr·ft·°F), better than 98% of steel grades. Thermal expansion is 12 µm/m·K (6.67 µin/in·°F).
Electrical3
DC01-EG conducts electricity at 10.8 % IACS, better than 94% of steel grades.
Chemical & Environmental3
Corrosion resistance is poor (22/100), better than 89% of steel grades.
Sustainability4
Producing a kilogram of DC01-EG takes about 25 MJ of energy and emits 2.1 kg of CO₂ — less than 82% of steel grades. Typical recycled content is 25%.
Manufacturability8
DC01-EG's machinability is good (55/100, better than 62% of steel grades); weldability very good (75/100); formability very good (80/100).
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Other DC01 tempers and conditions
DC01 is also supplied in 3 other conditions. The full side-by-side table is on the DC01 overview.
- HRDefaultChoose for thicker, lower-cost parts where mill scale and looser thickness tolerance are acceptable.250 MPa yield · 120 HB
- GalvanizedPick for outdoor or humid service where paint alone is not enough; zinc gives sacrificial protection but limits welding, forming radius and service temperature.250 MPa yield · 105 HB
- CRStandard stocked condition: bright, flat, tight-tolerance sheet for general bending, roll forming and light drawing.210 MPa yield · 100 HB
- EGChoose when a smooth paintable surface and tight thickness control matter more than coating life — thin zinc for indoor enclosures and appliance panels.210 MPa yield · 100 HB
Working with DC01-EG
Is DC01 easy to machine?
Soft and gummy — use sharp positive-rake tools, high speed and generous coolant to avoid built-up edge and burrs; ideal for punching, laser and shear cutting rather than turning.
Can DC01 be welded?
Excellent with all processes (RSW, MIG, TIG, laser, spot); galvanized versions need fume extraction, higher current and often a gap or Zn-compatible wire to avoid porosity.
Can DC01 be formed, bent or molded?
Very good cold formability — bend radii down to ~0.5–1×t, deep-draw modestly (use DC03/DC04/DC06 for severe draws); watch stretcher strain lines if the skin-pass has aged.
What surface finishes work on DC01?
Bare stock must be protected immediately — zinc plating, zinc phosphate + e-coat, powder coat or oil; galvanized sheet takes paint after a chromate/phosphate or Zn-compatible primer.
DC01 chemical composition (wt %)
Limits by weight percent from the governing specification, written the way the spec states them — a single maximum for impurities, a range for alloying elements, and the base element as balance. Nominal is the typical mid-range value.
| Element | Spec limit (wt %) | Nominal |
|---|---|---|
| CEN 10130 ladle analysis max | ≤ 0.12 | 0.06 |
| Mn | ≤ 0.6 | 0.3 |
| P | ≤ 0.05 | 0.02 |
| S | ≤ 0.05 | 0.02 |
| Sitypical for Al-killed CR sheet, not always specified | ≤ 0.05 | 0.02 |
| Alacid-soluble Al, killed steel | 0.02 – 0.07 | 0.04 |
| Fe | balance | — |
DC01-EG — frequently asked
What is DC01-EG used for?
DC01-EG is typically used for appliance panels, automotive body and bracket parts, electrical enclosures and cabinets, sheet metal chassis and covers, ductwork and housings and stamped brackets and clips. In short: european standard sheet.
What is the yield strength of DC01-EG?
DC01-EG has a typical yield strength of 210 MPa (30.5 ksi) and a tensile strength of 310 MPa (45 ksi) — weaker than 98% of steel grades. Strength varies by condition: see the 4 listed tempers.
Is DC01-EG easy to machine?
Reasonably — machinability is rated good (55/100, better than 62% of steel grades). Soft and gummy — use sharp positive-rake tools, high speed and generous coolant to avoid built-up edge and burrs; ideal for punching, laser and shear cutting rather than turning.
Can DC01-EG be welded?
Yes — weldability is rated very good (75/100). Excellent with all processes (RSW, MIG, TIG, laser, spot); galvanized versions need fume extraction, higher current and often a gap or Zn-compatible wire to avoid porosity.
What surface finishes work on DC01-EG?
Bare stock must be protected immediately — zinc plating, zinc phosphate + e-coat, powder coat or oil; galvanized sheet takes paint after a chromate/phosphate or Zn-compatible primer.
Can DC01-EG be formed, bent or molded?
Very good cold formability — bend radii down to ~0.5–1×t, deep-draw modestly (use DC03/DC04/DC06 for severe draws); watch stretcher strain lines if the skin-pass has aged.
What is the maximum service temperature of DC01-EG?
DC01-EG is rated for continuous use to about 200°C (392 °F). Strength falls off well before that limit — check the elevated-temperature data for load-bearing parts.
What is the difference between DC01-HR and DC01-CR?
HR is the default condition — choose for thicker, lower-cost parts where mill scale and looser thickness tolerance are acceptable. CR: standard stocked condition: bright, flat, tight-tolerance sheet for general bending, roll forming and light drawing. Yield strength is 250 MPa in HR versus 210 MPa in CR.
Can FabDigit make parts in DC01-EG?
Yes — DC01-EG is available for sheet metal with instant online pricing. Upload a STEP file to get a price and a DFM check.
Sources
- EN 10130 — Cold rolled low carbon steel flat products for cold forming — CEN (2006)
- EN 10346 — Continuously hot-dip coated steel flat products — CEN (2015)
- EN 10152 — Electrolytically zinc coated cold rolled steel flat products — CEN (2017)
- ASM Handbook Vol. 1: Properties and Selection: Irons, Steels — ASM International (1990)
- Machinery's Handbook, 31st ed. (machinability ratings) — Industrial Press (2020)
- worldsteel LCI data for cold rolled and galvanized coil — World Steel Association (2023)
- Mysteel / SMM — Mysteel / SMM (2026)
Property data is compiled from published supplier and standards handbooks and normalised for comparison. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.