Multipurpose Plastic · Photopolymer
Standard Resin
Standard Resin is a multipurpose polymer — workhorse sla visual resin. Typical values: 50 MPa yield, 1.18 g/cm³, rated to 75 °C. Available for Injection molding, 3D printing at FabDigit.
Properties
Typical room-temperature values in the Standard condition. Metric first, imperial in gray. The bars show where Standard Resin sits against the other 74 polymer grades in the catalog.
Datasheet
| Yield strength | 50 MPa7 ksi |
|---|---|
| Tensile strength | 65 MPa9 ksi |
| Hardness | 85 HRM |
| Density | 1.18 g/cm³0.043 lb/in³ |
| Specific strength (yield ÷ density) | 42 |
| Min service temp | -20 °C-4 °F |
| Max service temp | 75 °C167 °F |
| Electrical conductivity | < 0.001 % IACSinsulator |
| Machinability | Fair40 / 100 |
| Weldability | Not recommended5 / 100 |
| Formability | Not recommended5 / 100 |
Values are nominal handbook figures for design screening. Certified mill or lot data ships with every FabDigit order on request.
Against other polymer grades
Strength versus weight in the polymer family
Yield strength against density for every polymer grade FabDigit runs. Standard Resin is highlighted; hover a dot for its name, or open the interactive family chart.
Manufacturability
The process limits FabDigit's quote engine applies to Standard Resin. Design inside these and the part quotes instantly; outside them it routes to an engineer.
Injection molding
| Mold shrinkage | — |
|---|---|
| Wall thickness | — – — |
| Recommended draft | — |
| Pre-drying | — |
3D printing
| Technologies | SLA |
|---|---|
| Layer height | 50 – 300 µmdefault 100 µm |
| Minimum wall / feature | 1 / 0.5 mm |
| Build envelope | 300 × 300 × 380 mm |
| Supports | Yes |
| Anisotropy | Moderate |
Conditions and tempers
How Standard Resin is supplied and what each state is for. The default is what FabDigit quotes unless your drawing says otherwise.
| Condition | Best for | Yield MPa | Tensile MPa | Elong. % | Hardness |
|---|---|---|---|---|---|
StandardDefault Grade Modifier | Baseline grade — pick unless you need a special property below | — | — | — | — |
Heat treatment and post-processing
Operations FabDigit's suppliers routinely run on Standard Resin, ranked by how often they make sense for this grade.
Post-processing
| Manual Deburr | Deburrstandard |
|---|---|
| Edge Break (0.5mm) | Deburr |
| Heat-Stake Insert | Assembly |
| Ultrasonic Insert | Assembly |
| Laser Engrave | Marking |
| Press-fit Insert | Assembly |
| Silk Screen | Marking |
| CMM Inspection | Inspection |
| FAI Report | Inspection |
| Individual Bag | Packaging |
Surface finishes for Standard Resin
Coatings and treatments compatible with polymer on the processes Standard Resin runs on. Pick them in the quote configurator or call them out on the drawing.
Coating
- Clear Coating
- Conductive Coating
- EMI Shielding Coating
- Primer Coating
- Soft Touch Coating
- Tinted Coating
- UV Coating
- Waterproof Coating
Injection Molding Coating
- EMI Shielding Coating
- Soft Touch Coating
- Spray Painting
- UV Coating
Marking / Decoration
- Chemical Etching
- Embossing / Debossing
- Hot Stamping
- In-Mold Labeling (IML)
- Ink Stamping
- Laser Marking
- Pad Printing
Metallization / Functional
- Chrome Plating (Plastic)
- Vacuum Metallization
Coloring
- Dyeing (Nylon)
- Painting
Equivalent designations
Standards and trade names that resolve to Standard Resin in FabDigit's catalog. Equivalence is nominal — check the exact specification when certification matters.
- Trade names
- Standard SLA ResinSLA Standard Resin
Stock forms
Raw-material forms FabDigit sources Standard Resin in.
Property data is compiled from published supplier and standards handbooks and normalised for comparison; hardness values on non-Brinell scales are converted approximately for charting only. Manufacturability limits are FabDigit quote-engine defaults and may be relaxed by engineering review. Nothing on this page is a certification — request mill certs, CoC or material test reports with your order.